Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We are having a very strange echo issue at a remote location and we can not seem to figure out the cause nor can our TAC engineer at this point. The hardware deployment is as follows: 3845 Gateway IOS Version 12.4(11)T4 Two 3750 Switches in a stack c...
After resetting the UC520 to factory default it would be possible to choose between Keysystem of PBXsystem. Bud with CCA 1.5 or 1.0 it isn't possible to change this option, i get a red bar witch indicates that this setting is nog posible.!! I reset t...
Anyone seen this before? Call Manager version 5.1.1.3126-1Error:"Update failed. [491] The specified name has invalid characters or is not formatted correctly for this device type."The MAC address field on the page saids use last 10 characters, which...
Hi,I have:T1 PRI terminates on a catalyst6500 (catOS) I need specific DID #'s to go to the router instead of the CCM. The T1 PRI terminates on the catalyst 6608. Are there any doucumentations or practical ways on how accomplish this?TIA,Fred
HiI am facing a weird problem here; I had configured 3845 Router to be work as H.323 gateway for Cisco Unified Communication Manager 4.2. The interface to the PSTN is FXO - temporarily - until E1 is received.If I called the Analog line, I can receive...
I've been getting more involved with our call manager setup. Other than me installing phones, it has basically been on auto pilot. We have a list of allowed area codes that my boss gave the consultant when the Cisco voice system was initially insta...
Can someone explain what exactly the "\" is doing in this example? rule 1 /^\(758\)444\(5...\)$/ /\1\2/thus when you dial 7584445111 it becomes 7585111. I see how the end shows the different sets and that it should become 7585111. why does the "\" n...
Hello. I have an interesting problem when trying to ping an Avaya IPSI (IP Signalling Interface) board from any Cisco device. When I try and ping the device, from say, a 4506, It appears to time out on every other ping request. Example:#ping 172.1...
I am attempting to do click to dial from Outlook with Unified Communications Manager 6.0 and when I install the Cisco TSP the ciscotsp001.tsp is not showing up. I can install it on my laptop and it shows up but not on the desktops for this company. ...
I am having a problem with the handsets not working on model 7941 phones. The phones can only be used via the speaker feature. I have changed the handset and the handset cord and that is not the problem.
Is there anyway I can access this as a list of all numbers from a single button press. for example press services on a phone and get a list of names and numbers instead of having to select a director then submit a search?Thanks for your time. Scott
Hello,Is there any default password for users trying to logon to https://callmanager/ccmuser ?It will take ages to create passwords for every user using the callmanager administration. Thank you.
Hi, How can i check the call logs(calls made, to which number it was made etc.)from the call manager(version 5.1). Please guide me how I can view the above from the call manager.rgdsRajesh
Curious if anyone has seen this as it's really the opposite of what most folks seem to have an issue with.We recently had an upgrade performed to our VoIP router to address and issue where inbound calls only displayed the calling number and not the n...
I have come across an issue and wanted to see if anyone else has seen the following:Configuration - CUCM 6.1 cluster with ICT to CCM 4.13 cluster. Also, have GK H.225 trunks configured to a GK cluster. The problem is that when I make any change on ...
