Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
one of the requirements in the field notice is to have updated firmware and device pack as stated below. My question are: 1. Do I have to upgrade both firmware and DP?or 2. I can just upgrade firmware since I do not want to upgrade DP?http://www.cisc...
Hello, I have a remote site with a 3745. All the IP phones at that site register to a CM at the main site. So, outside calls come in on a BRI to the 3745, are PLARed to the CM across a WAN. The CM has a CTI Rt Point to the Unity AA. Sometimes,...
We're using a SIP implementation with CME and more often than not it performs excellently. Occasionally on long calls (over 30 minutes), the sound will cut out on our end even though it appears the call is still active. The only way to get it back ...
Hi,I've got a Sip line and I can receive the calls but I cannot take an outgoing call because the line dropped when I answer the other side. When I take an outgoing call, looking the debug ccsip, I notice that there isn't any codec negotiation.Can yo...
Having two problems with 7936 on CME 4.03.1. Was running cmterm_7936.3-3-14-0.bin and ran into a problem where when I pressed the conf button to conference the 3rd party nothing would happen. Conf members total would have been 3.2. I fixed this issue...
Need to display text (desciption) on a Voip phone when a call is completed. Using CCM express (vers 12.4T) on a 2811 router. Config follows:ephone-dn 1number 3667description 273 Door Intercomname CFD 273 Door Intercomhold-alert 30 originator
We have a habitual 911 dialer who hangs up before the call is complete. So when 911 answers no party is on the line- it happens almost daily.How can I catch this in the CDR or other report or log to identify the user?We have CCM 5.1 and 2800 series r...
Hi,i have a problem when try to add a new phone or dispositive in the CCM, i show this message: "Either the current has expired or access has been denied because of insufficient priviligies. Please Close the current window and open a new one". ......
I am connecting to a branch office with a VPN that is using Call Manager Express. I want to set up 4 digit dialing between this system and my main office that is using CUCM 6.1. I created a route pattern to call the branch office and that is working....
I have a CUCM 4.1 that I need to integrate with a VoiceBlue (SIP Trunk), but I'm having problems when it tries to call to a different region. All the calls with the regions that use G711 function normaly, but when I try to make a call to a region wit...
I'm upgrading my CME to 4.2 version and the process is 99%, is it normal ?for me not !CCME-EP-AUSTRALIA#sh proc cpu sortedCPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 93% PID Runtime(ms) Invoked uSecs 5Sec 1Min ...
Hello,The Cisco Call manager is version 4.2 using a private network of IP addresses.Regular IP phone calls are working well in every direction. The problem that I'm experiencing, is when two people, connected via Cisco VPN and using the Cisco IP Comm...
Do I need to upload a firmware for 7941g phones into cucm 5.13 or is the default firmware good to go?Thanks
Hi Guys, I have the following doubt:When I work G.729 for call external its use 24K for call, When I work G.711 for call locally its use 80K for call. Ask, If I will have 03 sites for example(Sao Paulo, Rio de Janeiro, Minas Gerais), if I work in Sao...
We have Emergency responder version 1.2(3a) sr2a and I need to import a switchport details file. When I am exporting the switchport details file I don't see anything in the location column.For the other column everything is OK. Do I have to rewrite a...
