Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, can anyone tell me more about the difference about Cisco Unity and Cisco Unity VM
i have a ISR router running 12.4 software with a PVDM2-8, i want to configure the router as a conferencing only dsp, the dsp calculator suggests the follwing configCLI Information for Optimal results. To match the DSP Calculator configuration with y...
Hi,I want to disable call forwarding and conference feature in CCM 4.2 i.e. user access to IP phone. Is it possible to do so for all users .Also, I would like to disable the same for individual IP phones.regds,aman
Hello all![ISP]---[3845-IP2IP-GW]---[CCM]I have a strange problem with my UCM 6.0.1(a) When I call to outside from ip-phone, I can't work with IVR and dial extension number (for example I call 97273565 and dial ext 233 after connect).I run debug on 3...
HiWe are having 4.1.3 cluster.We are not able to open the admin page frm the Publisher getting ERROR 500 internal server error.i'm able to open the subscriber admin page.Let me know your suggestions
dear sir, We've ccm 4.1(3)sr5d .1 pub & 2 sub in the iptel environment. Any doc. or guide how to perform the subject? That request should be done on receptionist ip phone which will auto forward to guard house after office hours. Please advise.than...
With CCM 4.x with gateways running MGCP, is there a way in CCM to carve out two channels off the PRI and dedicate those to their own route group? I tried to simply do it by creating seperate route groups of same PRI. But in customer config, channel...
Hello,I have the following error on event viewer of my MCS (CCM 4.x):"The driver detected a controller error on \Device\Harddisk0\DR0"Should i do something?Thanks for your help,Met
I have an MGCP gateway. Recently we got new DDI lines. 02075491950-2150. We use a 4 digit extension. so extension 1950 was created for a user. When the number 02075491950 is dialed, the debug on the gateway shows its delivering 491950 instead of 1950...
At first - excuse me for my EnglishI have 1760-V router with CME 4.05 - 7912 ip phone (Skinny)2 - SIP ip phone from D-Linkone FXS card with two FXS portI write dial-peer for Sip phone#dial-peer voice 1010 voip#destination-pattern 1010#session protoc...
I have CCM 5.1.2. I am trying to add the new phone type to register the new phones 7945 and 7965. I download the file and loaded it restart TFTP but the phone type is not showing up. I don't want to reboot ... unless it is necessary. Can anybody tell...
If we want to analyze over 100 area codes with a bolean statmement in a script, will this cause an excessive delay in the call flow? In our script, we want to do a get call contact info. With a bolean statement we want to say if area codes = (over ...
I have looked for a way to disable Web Access to a lot of phones with CM 4.1, but can't seem to find a way to do it with Device Pool, Enterprise Params, Service Params, or BAT.Any way to do it?
Hello,CME 4.1I am not sure what I am doing wrong. I want to restrict one phone from calling long distance. My config is...!dial-peer cor list long-distance member long-distance!dial-peer voice 113 pots corlist outgoing long-distance destination-patte...
Is it possible to have srtp between two ip phones in different clusters? Can one cluster be 4.1.X and the other one 5.X?Thanks.
