Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Spanning tree question:I have heard various opinions regarding using spanning tree on a switched network where voice traffic will be utilized and wanted to get some more thoughts on the subject.I can see certain situations in which spanning tree may ...
I'm trying to upgrade from CM 4.1.3 to 6.01 but have the following problem:My MCS 7825-H-2.2 is supported on CM 6.01 except the HDD is only 40gb. TAC said I can replace with an 80 gb drive but it must be a certain part# or the install will abort. I...
Hello everyone,We have an office that has the main line shared on all the phones.Is there a way we can have the calls routed to AutoAttendant during the day, for example when we have meetings and we don't want to be disturbed?I hope this can be accom...
How many DLU's are required for a VG224 for UCM 6.0?If you have a 7961 with a 7914 expansion module, do you need a DLU to cover the 7914? Or doe the 4 DLU's on the 7961 also cover the 7914 (sure hope so).thanks
Cisco SIP stations and Linksys SIP stations cannot send re-invites to my SIP Server. The SIP Server denies the request because the UAS does not increment (or change) the Session ID, when they send a new SDP message. Is there a software build for th...
We have three xml phone services, developed with sdk, that are three views on the Microsoft Active Directory.When I call the services from 7940 or 7985 model every view works fine.When I use 7941 or 7961, I watch the error in the object.The firmware ...
Guys,everytime i change a DN's partiton the phone becomes unreachable. scenario - i have a phone in partition internal and i change it to partition local.results - if i do a search in Directory number i get 2 of the same DN one in internal and one in...
Users stopped recieving email in their Exchange inbox as well as on their phone. Looking at the unitydignostic event viewer it is riddled with errors 10001, 119, 100, and 139. One thing odd is in Event 100 is: Exception occured and handled. File: e:\...
I am administering a multi-site environment connected via VPN. Currently, the remote site depends on a single Callmanager at the main site. The PRI is also located at the main site. This means that all of the call processing and paths for the remo...
We have a 7970 at the operator console and have a dilema. They need to be able to make a new call (dial out) even if a call is coming in. So in essence, even if 2 or 3 calls are coming in at once they need to be able to dial out to make a call bef...
Does anyone know of an effective way to test 5.1 CM backups? I would prefer that we don't build a test server just for this purpose but if that is the only way to do it I guess we will have to.
We have just deployed a 2851 router as an mgcp gateway with CCM 4.1 (3)...However, only one of the 30 channels availbale from the voice card installed in the router is used for calls. All the timeslots have been enabled using the controller E1 0/0/1 ...
on some calls we hear complete short sentences repeated during phone calls, example if external caller says "hello my name is joe smith and i work at"we hear "hello my name is joe " twice but we still hear the rest of the conversation. i am running ...
HI,I have a c2821 with two VWIC-2MFT-T1/E1 and one PVDM2-64, and want to do DSP resource sharing. I have tried to do by configure a dspfarm but without success. In the docummentation I find regarding this, they talked about NM-HDV2 modules not the on...
The secretary answer the phone and she has 4 lines on her phone. If she is busy on line 1, the call will will go the line 2 ,line 3 until the line 4 will call the 304(autoattendant). But il will like that able to use the that setup but able to transf...
