Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Im doing a fresh install of 5.1 and not migrating from 4.2 to 5.1. We want to export the phones from 4.2 with the MACs, DID, display names, etc. Can I do this with BAT?Thanks!Tommer
If the dialpeer have the same preference, this case is default 0. Does that mean the call will be distributed to the two ccms in round robin fashion, meaning one call to ccm1, the other call to ccm2? or the 2nd dial-peer will never used? or the call...
Hi people !Please help me understand what's happening. I have two 2801 with FXO ports, both of them registered with the CM and I can place calls throught them with no problem. They're MGCP gateways.Now I've configured two Route Groups, one for each g...
Is there any monitoring software to view how your traffic is being affected by QOS. Something to verify that a QOS configuration is doing what it is supposed to be doing.
Has anyone every been able to place a call from one IPcommunicator to another over a vpn tunnel? I'm getting one way audio or choppy voice quality. If I place a remote ipcom call to a office phone while on vpn it works properly.
I have a few 7960's that refuse to get an IP address. Even if I configure the 7960 with a static IP address it still does not communicate with callmanager. I've plugged in a known good 7960 into the switch port and it works fine. Everything seems ...
I have added new subscriber to the cluster. Everything went fine on the install. I can see this server from CCMADMIN and start services ect.When I go to SQL server group I do not see the server there. Do I have to manually add this to the Group?Th...
Hello,I have a problem found on 2 routers , they are c2800 with FXS ports ( VIC2-2FXS) , problem that when I connect the phone to port 0 , the 2 fxs ports become off-hook , even if the phone is on-hook , and I can't dial to these ports as they are bu...
Hello Is there a way by which i can configuring the bandwidth for a single isdn channel.We have Isdn pri between mumbai n chennai.This link carries voice as well as data and is configured for DDR.Now the codec used is g729 24kbps with overhead.A...
Below is the partial configuration.My Query is when 3/0/0 and 3/0/1 ports are busy with local calls (calls starting with non zero numbers), then the local calls should be established on 2/1/x which are configured for calls starting with '0'. This con...
how can i find out who has been calling my line besides looking on the phone for missed, received or placed calls can i do this in the call manager?
intermittent one-way audio and no-way audio on SIP TrunkCallmanager 4.2.3 ES15 on OS 2000.4.4a SR7Approximately 7 to 10 calls a day experience one-way audio and about the same experience no audio in either direction (at least those are the ones being...
I have a situation where local calling is available across more than one area code. Only some exchanges in the neighboring area code are local while others are not. I know how to create a route patterns for each individual exchange but I would like...
I need some advise on resetting a Cisco 7960 phone to default. I do not have the password. I have tried to reset the phone using **#, **#**, holding down # and typing 123456789*0# to no avail. The phones are configured SIP, App. Load: POS3-06-0-00 ...
I would like to connect Exchange 2k7 with CM4.1. Microsoft doesn't support it in a production environment. My question is, what solution can I use as maybe a VOIP gateway between Exchange and CM4.1 to allow this to work? I have seen implementation...
