Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi I'm trying to connect Cisco IP Communicator to UCCE 11.5 Environment any device not registered my laptop. I'm using IP communicator version 7 I think this version not supposed I have to upgrade 8 but still same issue. I'm using windows 10 Pro...
Hi I have 200 dids,and 250 phone I want to assign 50 non did numbers and assign a caller id 2430XXXX for outgoing (external) call .And another non did xxxx I want to assign caller id internaly(yyyy)and externaly 2430YYYY How can i do that? Thanks
Hi All, Would just like to validate if we have multiple PVDM installed on the Voice Gateway, are the resources will be also doubled? Ex. PVDM3-256 has a total of 256 channels lets say for low-complexity codec such as G711. If we have 2 PVDM3-256 in...
We're about to integrate CUCM with ActiveDirectory. We'd like to set the LDAP Attribute for User ID to "telephone number" to preserve the existing users we have in CUCM (which currently match their 4-digit directory numbers in the existing local data...
Hi i have unity 5 with cucm 7, and call handler 8997 (auto attendant to transfert DN), in gateway i have voice port 1/0/16 and ligne PSTN, how to assign this ligne PSTN to voice port 1/0/16 to call handler example: if call from external to ligne P...
Hi Team I'm in process to upgrade UCCX version 9.0.2 to version 11.5, i installed the ciscouccx.refresh_upgrade_v1.11.cop.sgn and the ciscocm.version3-keys.cop.sgn but all the installation fails whit the error in the image attached The documentat...
Hello, I have CUC 10.5x cluster & default CUC message aging policy has been apllied for all users. But I can see some of the users have old messages. It seems message aging policy is not functioning properly, Please advise.
Doing a search for firmware and config files for 7940 SIP phone but none are showing Shows load files and lots of other files though CUCM 7.2.1 doesn't show SEP<MAC>.cnf.xml file for registered phone When doing a show CDP neighbors on switch, shows t...
Hello People! I want to purchage a 7937G conference phone, but as I understand it needs a licence to work. Once I connect it to the network, does it request for the licence immediately? Is there a manual on how to install the licence? Thanks
Hello Everyone, Very Good Morning, In my environment, I have SIP trunk configuration as gateway on CUCM and ON VG router is also having same. Recently, i did the changes in SIP trunk ( ip address changed). remaining was the same configuration,...
Hi there, I want to change from internet / Telephony operator where the current one has analog phone line, and the next one will be using Voip. Issue is that my alarm system is using and needs an analog phone line ... I would like to know if / wh...
Hi, We have plenty of Cisco CP-7821 phones, and our organization want to implement a open source Elastix Software (v2.5). i have installed the system and configured it, but can't configure the telephones to connect to it. the phones keeps telling me ...
Hi everyone, I'm facing some issues when trying to forward calls. I'm think is not a partition issue because of when I use the Forward All option it DOES transfer call correctly but if I try any other option (even using the same DN I used in FW all...
I have two phones that share a DN. We want to route to a cell via SNR when the two desk phones are not answered. Internal calls to the DN forward on to the cell phone, but external calls to the DN just ring at the desk phones. I have my user creat...
Hello community, I have to configure a FXS port for a parlofoon, this a analog device close to a door which enable to ring a bell and user inside the office can remotely open the door. I have configured this FXS port, but enduser told me if someo...
