03-31-2009 01:52 PM - edited 03-15-2019 05:13 PM
Hi, I can't access to CUCME by GUI. When I put the username and the pass, then, the web page get to blank.
The commands web admin system name admin password cisco and ip http server are run.
Regards
Solved! Go to Solution.
04-02-2009 08:17 AM
Hello,
Please verify that you have the following files on your flash:
Admin-user.html
Admin_user.js
CiscoLogo.gif
delete.gif
dom.js
downarrow.gif
ephone_admin.html
logohome.gif
normal_user.html
normal_user.js
Plus.gif
sxiconad.gif
Tab.gif
Telephony_service.html
uparrow.gif
xml.template
xml-test.html
These are all of the files necessary to enable full GUI functionality.
Hope that helped, if so please rate.
03-31-2009 02:08 PM
Hello,
Do you have "ip http path flash:" configured?
03-31-2009 03:12 PM
Dear Kenneth...Yes
03-31-2009 03:32 PM
Hi to access the GUI and allow the admin to add remove DNs from web interface:
ip http server
ip http path flash:
telephony-service
web admin system name admin password cisco
dn-webedit
time-webedit
Hope this help
David
03-31-2009 03:55 PM
Cool, I'm going to re-configure and I will show you the result.
04-01-2009 01:54 PM
Hi..fail. :(. I think that upgrading will be fine.
04-02-2009 08:02 AM
Hi David
I upgraded to 124-22.T (Cisco 2811), but i still can't access to GUI. I put the user and passw and then it show me the page in blank. Pls.,see the command
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:
telephony-service
em logout 0:0 0:0 0:0
max-ephones 42
max-dn 80
ip source-address 10.175.206.1 port 2000
system message CME
user-locale ES
network-locale ES
time-zone 18
time-format 24
date-format dd-mm-yy
voicemail 3120
max-conferences 8 gain -6
web admin system name admin password cisco
dn-webedit
time-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Mar 31 2009 15:20:31
I don't know what happens
04-02-2009 08:17 AM
Hello,
Please verify that you have the following files on your flash:
Admin-user.html
Admin_user.js
CiscoLogo.gif
delete.gif
dom.js
downarrow.gif
ephone_admin.html
logohome.gif
normal_user.html
normal_user.js
Plus.gif
sxiconad.gif
Tab.gif
Telephony_service.html
uparrow.gif
xml.template
xml-test.html
These are all of the files necessary to enable full GUI functionality.
Hope that helped, if so please rate.
04-02-2009 10:12 AM
Dear Kenneth, the problem is solved.
Thanks a lot!!
10-21-2009 03:45 AM
Hi All,
i have CME version 7.1 with IOS 12.4(24T1)and i experienced the same problem with the GUI interface. i found that the problem came from copying the GUI files using a flash reader, when i uploaded the files using the archive command and used the command ip http server path flash: ,the GUI worked fine but after a restart.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide