Other Network Architecture Subjects

Hi all,I need to set up network monitoring through web browsers using MRTG, over my network I had 2 Cisco 2503 router, 1 Cisco 2950 switch, but I do not reallyknow what to do? What are the setting I need do at the router and the switchand also at the...

Can someone tell me the difference between CAR and traffic shape for limiting bandwidth rate access?Best Regards.

We would like to lock down a WAN connection using access-lists. This is as well as others security products, the main reason for this is to limit what goes across the links.I have created an access-list that permits the main application ports that we...

1)NM-1CE1U just only work on ISDN?2)NM-1CE1U has the dsu/cus?3)what is the controller ? it 's a hardware ?4)NM-1CE1U i can use it seperate the clear E1?5) IF i have 30 branch offices ,i can use NM-1CE1U connect to clear E1 ,and then make 30 office...

What is the difference btw EMI and SMI?So if they are different what are the things that one can do while the other can't?If i am using it for access layer in an enterprise network, which image would u recommend?

Hi Friends, I am having a 2511 router with 2 sync ports and 6 sync/async ports.Both the 2 sycn ports are occupied.Now i got to terminade a normal 64k Leased line on this router . will my sync/async ports support this LL ?? or should i apply any ...

I have 3 Internet connections with 3 different ISP's, each with 8 IP addresses.If all these connections terminated at a single router.Can I do NAT to map all these 3 different segments of IP addresses to one SINGLE contiguous inside IP addresse rang...

Having upgraded Whats Up Gold 6 (bundled with Cisco Works) to Whats Up 7 for the better reporting etc - the integration with Cisco View doesn't work (all the URL's called by Cisco View are now incorrect!!)Any way around this?404 from WhatsUP explains...

hi, I have 6509 switch with MSFC , the switch is operational ..but I cannot see the utilization percentage on the utilization monitor on the supervior engine !!!do I have to enable this or I have problem in my switch?

Hello,I have a 1605-R, that when powered on the System OK light on the front panel keeps blinking, normally indicating the boot process. I let it go for 15 minutes just to be sure it dosen't eventually end up booting properly.I can't get access to t...

In the past, i used old 4000 routers for IP routing. One IP subnet had some apple (Mac) machines connected by hubs. These MAC machines had to be seen by other MAC machines via appletalk choose. Besides, these machines had to browse the internet.Re...

Hi Rizwan,I've tried a snmpwalk for ifInOctets/ifOutOctects before and I could only retrieve traffic information up to four interfaces only namely: GigabitEthernet0/0, GigabitEthernet0/1, Null0 and Loopback0. The MIB tree in my 7401 router does not c...

I have a Cisco 3620 connected to an Internet frame circuit. Behind the router I have a Checkpoint/Nokia firewall. Behind the firewall I have a 1721 router with a default route to the Checkpoint inside interface. When the Internet circuit goes down, I...

Hi,I have a Cisco 2600 router that my company as lended to me, and i want to set it up with my cable internet modem. What WIC do I need to make it work? It currently has a 56k/64K serial DSU/CSU. I will be connecting about 10 computers through th...

I have a Cat5009 switch.I don't know how to config a syslog server on the switch.I searched and found a command(set logging server....),but I can't find this command on my Cat5009,maybe the OS ver is too old.shqdcn-s> (enable) set ?Set commands:-----...