04-10-2003 11:51 AM - edited 03-02-2019 06:34 AM
I have this issue:
R2: running area 0 and 3 (ABR)
R1: running area 3 only (Internal router) and also is ASBR
I created a loopback interface on R1 assign ip address 150.50.200.1 and then
advertise this network in RIP. I then redistributed RIP into OSPF, hoping that I would see this route on my R2.
Area 3: 150.50.17.0/24
RIP is on 150.50.200.0/24
Redistribution commands.
rotuer ospf 1
redistribute RIP subnets metric-type I metric 20.
I don't know what I am doing wrong, but R2 is not seeing this route as an E2.
Thanks,
04-10-2003 12:14 PM
hi
You could try to do the following:
router ospf 1
redistribute connected subnets route-map "loopback"
!
route-map "loopback" permit 10
match ip address 50
!
access-list 10 permit 150.50.200.0 0.0.0.255
So you just redistribute connected networks and filter all except the loopback out.
Hope that helps
Roger
04-10-2003 12:18 PM
Thanks Roger !
I should have thought about this, but didn't click.
Thanks Again,
Regards,
04-11-2003 10:06 AM
try to clear out your type 5 lsa's bu doing a 'clear ip ospf redistribution '
Also it would see it as an E1 because you are specifying metric-type 1
04-11-2003 01:26 PM
It still didn't work. Here is the configs.
r2#wr t
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname r2
!
!
ip subnet-zero
no ip domain-lookup
isdn switch-type basic-ni
!
!
!
interface Loopback0
ip address 200.0.0.2 255.255.255.255
no ip directed-broadcast
!
interface Ethernet0
ip address 150.50.17.2 255.255.255.0
no ip directed-broadcast
media-type 10BaseT
!
interface Ethernet1
no ip address
no ip directed-broadcast
shutdown
media-type 10BaseT
!
interface Serial0
no ip address
no ip directed-broadcast
encapsulation frame-relay
no ip mroute-cache
logging event subif-link-status
logging event dlci-status-change
frame-relay lmi-type ansi
!
interface Serial0.24 point-to-point
ip address 150.50.24.2 255.255.255.0
no ip directed-broadcast
frame-relay interface-dlci 103
!
interface Serial0.256 multipoint
ip address 150.50.100.2 255.255.255.224
no ip directed-broadcast
ip ospf message-digest-key 1 md5 cisco
frame-relay map ip 150.50.100.2 102
frame-relay map ip 150.50.100.5 102 broadcast
frame-relay map ip 150.50.100.6 107 broadcast
!
interface Serial1
no ip address
no ip directed-broadcast
ip ospf network broadcast
shutdown
!
interface Serial2
no ip address
no ip directed-broadcast
shutdown
!
interface Serial3
no ip address
no ip directed-broadcast
shutdown
!
interface BRI0
no ip address
no ip directed-broadcast
dialer string 963-6000
interface BRI1
no ip address
no ip directed-broadcast
shutdown
isdn switch-type basic-ni
!
interface BRI2
no ip address
no ip directed-broadcast
shutdown
isdn switch-type basic-ni
!
interface BRI3
no ip address
no ip directed-broadcast
shutdown
isdn switch-type basic-ni
!
router ospf 1
area 0 authentication message-digest
network 150.50.17.2 0.0.0.0 area 3
network 150.50.24.2 0.0.0.0 area 1
network 150.50.100.2 0.0.0.0 area 0
network 200.0.0.2 0.0.0.0 area 22
neighbor 150.50.100.5
neighbor 150.50.100.6
!
ip classless
!
!
line con 0
transport input none
line aux 0
line vty 0 4
!
end
r2#
r1#wr t
Building configuration...
Current configuration : 834 bytes
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname r1
!
!
!
!
!
!
ip subnet-zero
no ip domain-lookup
!
!
!
!
interface Loopback0
ip address 200.0.0.1 255.255.255.255
!
interface Loopback10
ip address 150.50.200.1 255.255.255.0
!
interface Ethernet0/0
ip address 150.50.17.1 255.255.255.0
!
interface Serial0/0
no ip address
shutdown
no fair-queue
!
interface Serial0/1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
redistribute connected subnets route-map cisco
network 150.50.17.1 0.0.0.0 area 3
network 200.0.0.1 0.0.0.0 area 11
!
ip classless
ip http server
!
access-list 1 permit 150.50.200.0
route-map cisco permit 10
match ip address 1
!
route-map cisco permit 20
!
!
line con 0
line aux 0
line vty 0 4
!
no scheduler allocate
end
r1#
r2#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
U - per-user static route, o - ODR
Gateway of last resort is not set
200.0.0.0/32 is subnetted, 5 subnets
C 200.0.0.2 is directly connected, Loopback0
O 200.0.0.4 [110/65] via 150.50.24.4, 01:54:08, Serial0.24
O 200.0.0.5 [110/65] via 150.50.24.4, 01:54:08, Serial0.24
O IA 200.0.0.6 [110/65] via 150.50.100.6, 00:07:22, Serial0.256
O IA 200.0.0.7 [110/75] via 150.50.100.5, 00:07:22, Serial0.256
10.0.0.0/24 is subnetted, 1 subnets
O 10.1.1.0 [110/74] via 150.50.24.4, 01:54:08, Serial0.24
O E2 192.168.1.0/24 [110/20] via 150.50.100.5, 00:07:22, Serial0.256
O E2 192.168.2.0/24 [110/20] via 150.50.100.5, 00:07:22, Serial0.256
150.50.0.0/16 is variably subnetted, 5 subnets, 3 masks
O 150.50.7.0/25 [110/74] via 150.50.100.5, 01:51:45, Serial0.256
C 150.50.17.0/24 is directly connected, Ethernet0
C 150.50.24.0/24 is directly connected, Serial0.24
C 150.50.100.0/27 is directly connected, Serial0.256
O IA 150.50.5.64/27 [110/138] via 150.50.100.5, 00:07:24, Serial0.256
O E2 192.168.3.0/24 [110/20] via 150.50.100.5, 00:07:24, Serial0.256
r2#
04-14-2003 04:42 AM
What does a ' sh ip o dat external 150.50.200.0 ' show ?
Also you referecne ACL 1 in your route-map , I do not see ACL 1 in your config
04-14-2003 05:11 AM
I would like to see a sho ip ospf neighbors on these routers. I dont think they are connecting. What does the wildcard 0.0.0.0 do on the ospf network statements?
04-14-2003 07:12 AM
i suppose that R1 and R2 are not OSPF neighbors..that's why R2 don't see routes from RIP route redistributed into OSPF
plz add "sho ip ospf nei" command output
thanks
04-14-2003 01:18 PM
add the command output for R1 and R2
show ip ospf nei
&
show ip ospf database
...........
04-14-2003 01:34 PM
Thanks everbody in the forum ! I tried all the suggestions I received from you guys, but still couldn't make it to work. I checked configurations tons of times to see if there was any glitch. The weird thing was that R2 didn't have the entry for the route 150.50.200.0/24, but the routers beyond the R2 had that entry with default gatway through R2.
I got so frustrated that I erased both r1 and r2 completely, reloaded them and reconfigured them. Bingo! Everything is working now with the same configs I had before.
Anyway ! Thanks everyone for so responsive.
Regards,
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide