10 express 500 and 2 2960 are uplinked to a 3750 . PC's getting dhcp address from all 2960's and 3750 itself .but not with express 500 .
10 express 500 and 2 2960 are uplinked to a 3750 . PC's getting dhcp address from all 2960's and 3750 itself .but not with express 500 .
Have a sup 720 that boots into rommon . I can see that the supervisor config register is not right . How do I change it on the supervisor once its booted up ? I remote command into the supervisor but don't see an option to change the config re...
Does anyone have a screen shoot of the VideoConferencing manager on a 3515 MCU? Is it possible to integrate the manager to a users Outlook calendar? It says on the datasheet that there is an option to schedule video calls from an Outlook client but...
WS-X6148-GE-45AF in 6509 don't support broadcast control, please let me know if there is any other alternate to control broadcast traffic.
Hi all, just a quick one,Where in sh ver is the chasis serial number?.
I' ve a 6509 with a SUP1A-2GE.I see these messages after I power cycle the switch and I know that the Catalyst 6500 isin the SP ROMmon:System Bootstrap, Version 5.3(1)Copyright (c) 1994-1999 by cisco Systems, Inc.c6k_sup1 processor with 65536 Kbytes ...
I have two Cat6500 in redundancy. I would like to connect Server NIC1 to Cat6500 1 and Server NIC2 to Cat6500 2 i.e. Active/Active. Both NIC's will be sending data. Is it possible with Cisco switches. Any Cisco link will be helpful.Thanks
Hello,We have several Cisco 2960 switches and we have a problem after upgrading IOS.We had : c2960-lanbasek9-mz.122-46.SENo problem at all transfering IOS files with tftpNow : c2960-lanbasek9-mz.122-46.SEWith this IOS, every transfer crash. Only a fe...
is it possible to use a 100basefx Gbic in a Catalyst 3750G-12s ?
Hi. I have kind of a design question on voice and data vlan routing. Equipment involved:Router: Cisco 2811 for CME, two Fastethernet ports and NME moduleSwitch1: Cisco Catalyst 3750G-12S-S SMI 12 port Fiber with with sfp modulesSwitch2: Cisco Catal...
What is the difference between the show service module command output versus th show controllers output? Is one better or more accurate than the other? Are these layer one or two statistics? Thanks.
Hi all,I am not able set encapsulation on the gig port of one of my switch as I want to allow only few vlan on any portSwitch: WS-C4507R-EIOS: 12.2(44)SG1 ((cat4500e-ENTSERVICESK9-M))Switchport capability:sh int GigabitEthernet1/10 switchportName: Gi...
I am trying to configure an 881 for a remote location, the port the phone(s) (tried both a 7960 and a 7941G) is connected to will not go on the Voice VLAN, it will obtain an IP address on the data VLAN (as will the computer connected via the phone). ...
Hi,I have got a number of 3700 routers without compact flash memory.I wish to install IOS on the On-board DRAM. Can someone guide me on how to install IOS on the on-board memory and not the flash card?Thank you.
I'm configuring qos and transmit queuing on a Cat4948 switch, as per below. I cannot find any commands that allow me to view the transmit queue usage. The only commands I can find just show me the config.interface g1/1 qos trust cos tx-queue 1 ba...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |