How do I create a self signed certificate that does not use MD5 hash? I have an ASA that needs to pass a scan, and this is the only thing showing up, port 443 for Anyconnect fails due to weak hash MD5.
How do I create a self signed certificate that does not use MD5 hash? I have an ASA that needs to pass a scan, and this is the only thing showing up, port 443 for Anyconnect fails due to weak hash MD5.
Hi All, This is our set up:Client -> Router -> Core Switch -> Subnet 1 -> Subnet 2Is there a way to configure the Router (and Client) to allow the Client access to both subnet 1 and 2 behind the Ro...
Hi Guys,Can anyone tell me whether the Cisco Anyconnect VPN client is supported on iPad?Thanks,Lake
This is the routing table of are VPN_ASAroute outside 0.0.0.0 0.0.0.0 20.90.21.1 1route inside flair 255.255.255.255 172.18.0.1 1route inside 20.110.208.0 255.255.240.0 172.18.0.1 1route inside 20.110.216.0 255.255.255.0 172.18.0.1 1 route outside 0....
HI , I have set a tunnel between Cisco pix 6.3 and Cisco Router 7200. Show Isakmp sa showing below detail on Pix Total : 1Embryonic : 0 dst src state pending created xx6.x71.x29.x68 x2.1x7.52.1x1 QM_IDL...
Hello everyone!I have a trouble with PPTP VPN between Windows clients and Cisco 2921 router with RADIUS (IAS) authorization. When I try to connect to Cisco 2921 from Windows 7 using MS-CHAP v2 I receive error 778: it was not possible to verify the id...
Hi,We have a cifs share to a user shared drive, where every user has a personal folder. How do you lock this down so that each user can only see their own folder? At the moment everyone can browse and open anyone else's files/folders.Thanks in adva...
Hi,I am very new to Cisco routers and IOS so please excuse any ignorance on my part, we are a small start up and I am a make shift sysadmin. We have purchased a Cisco 892W router to provide a fixed VPN tunnel to our VPC hosted by Amazon. The router s...
Iam configuring Site to Site tunnel between ASA 5505. My topology: 10.77.59.0 ==Lan==|ASA1|=========|ASA2|==192.168.1.0 and One more tunnel bw 192.168.1.0==|ASA2|=====|Draytek|==192.168.16.0 Both the tunnel is up any from inside PC i can ping a...
Hi,We have a datacentar with ASA device and couple od branch offices with 1841 routers and one branch office with a 3650 L3 switch. Is it possible to make VPN connections (IPsec) between 1841's and 3650 on one side, and ASA on the other, where ASA ...
I am using a cisco asa5520 and i have set up remote access vpn with an AnyConnect connection profile.In the connection profile i have set up that users should authenticate using both certificate and AAA.Due to a high security requirement, the user ce...
I have a site to site VPN. On my hub router I am seeing the following message EVERY minute in the log!%sys-6-stacklow: stack for level DMA/Timer Interrupt running low, 36/9000I have been trying to figure out what the DMA/Timer Interrupt is and what i...
We currently have a couple of IPSEC SPAs that we are using to terminate site to site vpn tunnels in vrf mode. We are looking at leveraging this hardware to also terminate remote access vpn using PKI to avoid the aggressive mode security issues. I w...
Hello,Does anyone know if it is possible to run a point-to-point GRE tunnel over the GETVPN technology?TIADave
I have an ASA that I've set up for remote access. The VPN group I'm using is "companyVPN". The VPN client connects and I can see the Client-to-ASA traffic crossing the tunnel because the client shows packets being encrypted and the ASA shows them b...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-27-2024 02:28 AM | ||
04-26-2024 05:58 AM | ||
04-25-2024 07:36 PM | ||
04-24-2024 01:26 AM | ||
04-19-2024 08:08 AM |
User | Count |
---|---|
6 | |
4 | |
1 | |
1 | |
1 |