Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

VPN DPD on ASA ios v 8.6.1

Hello to every one:-

1)i want to know the show command to verify the DPD on ASAs. i tried couple of commands but unable to findout DPD is enable on my ASA.

2) when i try to enable the DPD on ASA the old commands was below.

tunnel-group DefaultL2LGroup ipsec-attributes
isakmp keepalive threshold 10 retry 2

but on my ASA their is no command as specify above to enable isakmp DPD.

My ASA shows me.

ASA(config)# tunnel-group x.x.x.x ipsec-attributes

ASA(config-tunnel-ipsec)# isakmp ?

tunnel-group-ipsec mode commands/options:

  keepalive  Configure ISAKMP keepalives

configure mode commands/options:

  disconnect-notify  Enable disconnect notification to peers

  identity           Set identity type (address, hostname or key-id)

  nat-traversal      Enable and configure nat-traversal

  reload-wait        Wait for voluntary termination of existing connections before reboot

ASA(config-tunnel-ipsec)# isakmp disconnect-notify

1)The isakmp disconnect-notify looks like new command to enable DPD on ASA??

2) anyone please let me know if their is any show command available to check the DPD is enable......??

Thanks a lot

2 REPLIES
Cisco Employee

VPN DPD on ASA ios v 8.6.1

If in doubt whether command is enebaled by default on ASA use the "all" modifier when doing show run.

From ASA 9.0

# sh run all tunnel-group 6.1.2.2 ipsec-attributes

tunnel-group 6.1.2.2 type ipsec-l2l

tunnel-group 6.1.2.2 ipsec-attributes

ikev1 pre-shared-key *****

peer-id-validate req

no chain

no ikev1 trust-point

isakmp keepalive threshold 10 retry 2

no ikev2 remote-authentication

no ikev2 local-authentication

From ASA 8.4

bsns-asa5505-19# sh run all tunnel-group BERN ipsec-attributes

tunnel-group BERN type remote-access

tunnel-group BERN ipsec-attributes

ikev1 pre-shared-key *****

peer-id-validate req

no chain

no ikev1 trust-point

no ikev1 radius-sdi-xauth

isakmp keepalive threshold 300 retry 2

ikev1 user-authentication xauth

no ikev2 remote-authentication

no ikev2 local-authentication

New Member

VPN DPD on ASA ios v 8.6.1

i think DPD is enable by default and your command helps and now i can see isakmp keepalive commands under tunnel group.

but if i want to modiy it the config and type (? make)  after isakmp no keepalive option popin. four options available its define below.

ASA(config)# tunnel-group x.x.x.x ipsec-attributes

ASA(config-tunnel-ipsec)# isakmp ?

tunnel-group-ipsec mode commands/options:

keepalive Configure ISAKMP keepalives

configure mode commands/options:

disconnect-notify                            Enable disconnect notification to peers

identity                                                Set identity type (address, hostname or key-id)

nat-traversal                                      Enable and configure nat-traversal

reload-wait                                          Wait for voluntary termination of existing connections before reboot

ASA(config-tunnel-ipsec)# isakmp disconnect-notify

its look like isakmp keepalive command no more avaible or replace by isakmp disconnect-notify.. 

i am using 8.6.1 version of ios

237
Views
0
Helpful
2
Replies