The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello,We are configuring virtual CSR8000 over AWS infrastructure, and have configured IPSec tunnel for voice traffic.Tunnel is configured with Public IP tied to physical interface, and RTP endpoint tied to Loopback interface. With this setup tunnel d...
Hi all,this ist a part of our switch port config on a C9300 with an IOSXE 17.9.X:+++interface GigabitEthernet1/0/7description RADIUS Portswitchport access vlan XYswitchport mode accessauthentication priority dot1x mab+++now due to some internal issue...
Hi, I have 25 FTD Cluster and I want to configure an automatic scheduled backup for every week. So I have 50 backup files every week. The problem is, that the new file do not overwrite the old, so on the second week I have 100 files, on the third 150...
Hi, i have problem of synced betewin my 2 switchs nexus 7.0.3.i7.3I use feature BGP, LACP and VRRP (also VPC etc..)But it's impossible of configure correctly the protocolI have many errors :One : In log :%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 9-1...
HI, we have project requirement to integrate the Iridium Satellite phone integration with Cisco PABX to make a calls in case of emergency. Can you please suggest, what can we achieved with this interface.1) can we make calls on any number at cisco PA...
Hello Folks, I have a pair of ASA5516 with HA mode, ISP provides a high-speed WAN 500Mbps up/download, while doing some speed tests recently we noticed that all our tests from the inside network are not bypassing 100mbps, I checked all inside/outside...
We are using Webex Calling When a caller places a call, it rings twice and then goes silent. On the recipients end it rings the set number of times (6 in our case) and then goes to voicemail if the recipient cannot get to the phone in time.. The cal...
Hi, I recently purchased a new 8861 3pcc K9. It is asking for an activation code. I purchased this phone for my small business and I'm the only user. I can NOT figure out how to find this code or get past this. Thanks in advance for your help.
Dear all, Currently we've obtained ASR1001X and the new redudancy configuration requires us to pass dot1q traffic through 2 interfaces. It seems we cannot familiarize ourself with trunking and vlan interface when it comes to pure L3 devices. A diagr...
Hi AllHoneywell are installing some devices on our network using the Bacnet protocol, this protocol I believe uses broadcasts to communicate, I believe there is a solution for the broadcasts issue called BBMD?Has anyone got bacnet working by enabling...
Hello All, I am the one who face this issue or this is something bug ?I am not able to edit start time in Real time Data of RTMT tool, Its just greyed out ( Drop down button also not working) .CUCM - 12.5.1.13900-152
Ask Me Anything Forum - Drive to 15X Welcome to the Cisco Support Community Ask Me Anything discussion! Are you considering upgrading or migrating your UC applications to version 15.x, such as CUCM, CUC, IM&P? If you're looking to learn more about...
I've configured DHCP relay on the FTD and I have a 2nd FTD as a backup default gateway. x.x.x.1 and x.x.x.2 respectively. However something is wrong. When I enabled DHCP relay on the .1 FTD only, the DHCP relay wouldn't work and then I enabled thi...
Hi I tried to write these commands in CLI (using Putty) for cisco ISR1100-4G but it seems like the VLAN command is not recognized.Regards,Aria Step 1Ensure that the router is in the factory fresh mode. If the router is not in the factory fresh mode,...