Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi All, Anyone know what the light mean on 7825 that running IP IVR server ? I cannot seem to find anything in Cisco's support and we have one with a purple light. But until now, the server is working fine.I just afraid, maybe it will indicate the er...
Has anyone ever heard whether Cisco certifies SIP providers? If so, does anyone have a list of these providers.Thanks,
Hi Everyone,I built a VM using a downloaded OVA template for CUC 9.1(0) although my CUC disk version is 9.1(1a). This OVA template is the last one uploated at cisco.com, and the installation fails with a critical stop. Please refer to the attached fi...
Hi Guys,i have 7962 phone attached to it two 7915 modules each with 12 buttons so the total is 24 buttons.what is the configuration commands needed to show the 2nd page on each module?I mean i need to add more than 24 speed dials .Thanks in advance.
Hi,Need to upgrade old version of CM(6) to BEk which will have CM 9.1. Now I want to know if the following devices can be supported in this new CM version.Cisco SIP 3911ATA 186Cisco 7906If there is documentation. I will highly appreciate. Thanks!
We have existing sbin files for 7912 but am not sure if they're the correct files. And missing the ones for the 7960. Had them in storage but are looking to use them nowCan someone please adviseThanks in advance
Hi,I have two 7941's that are stuck in upgrading mode and even after a factory reset they will not do anything else apart from stick in upgradinghow do i fix this ?thanks
I'll be moving a customer from a 4x cluster to a 7x cluster over the weekend. Some things I have noticed is that MGCP dial-peers are added by CUCM. When we move from the older cluster to the newer cluser should we delete the dial peers created by...
We are getting following error and wuld like to know solution for it.Here is the error message from the Gateway:%VOICE_IEC-3-GW: H323: Internal Error (H323 Interworking Error): IEC=1.1.127.5.21.0 on callID 14269 GUID=80FC8A6 ...
Buenas tardesTengo un problema, tengo implementado una central IP con 4 IVR, y necestio poder limitar las llamadas, cada cuatro minutos de una llamada se corte automaticamente con un previo aviso automatico de que la llamada sera cortada, alguna idea...
Hi all, I've configured a unified SRST with MGCP fallback and I think everything is configured properly, but phones never try to register With the SRST,so, when I issue the command debug ephone detail. nothing appears. I'm using CUCM 8.6.2 >> 10.10....
Hi friends, I have SIP IP PHONES that do not send music on hold to SCCP Phones, I have revised the configuration and I don't find the solution. Someone has any answer to solve this issue. My CUCM is 9.1 BE6K.Thank you
Can someone please help, I have Auto Attendant setup and when a customer ring after 5pm when the company close, the call get forwarded to a manger mobile number, can any one please show me where I can change the forwarding in CUCM?Thnaks
My client wants to monitor status of sip trunks. I know with CUCM version 8.5 we have capability to turn on Option Ping on CUCM. I just wanted to see if we can generate Alarms and send email as soon as CUCM is unable to reach a perticular Destination...
I have the cucm 9.0 I install and configed cucm pub sub ok, the ip phone can register to pub,but when I change the phone to register that sub,then can't registerafter I googled some document,I checked the following 1. Network connectivity between the...
