Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hayi have 10 sip third party yeakink phones( in cyprus) that register to cucm manager 9.1 (in israel)for cyprus local calls ,i need to create secure sip trunk from voice gateway (in syprus) to kmt provider (kmt works only in secure mode)or create se...
Ho we were using unity server 5.x with partner exchange 2007 server. but the exchange server team already migrated exchange server to office 365. Now we are getting message server offline error when accessing voice mail.please can some body post docu...
Dear All,I need 1 help i have Cisco CME -3925 around 125 Ip phone registering in CME .my issue is IP-phone not getting ip address some times some phone getting ip address some times some phone getting ip address i configured DHCPin CME its self prov...
Hey,So we are testing an integration with a fax server from a voice gateway. We have an FXS/DID card in the voice gateway with lines connecting to the fax server (FXO I would assume). My understanding was that FXS ports could not send digits down to ...
Hello Guys, i am running cucm 8.5 and using the single number reach.when the SNR is used internally it works well.but when a call is placed from the PSTN or cellular provider number, i cannot see the actuall calling number on the cell phone that has ...
Hi my name is Henrik Jensen.We have an ATA 187 when we telnet to port 32000 we get MXP interface.Is there away to set username and password or stop the port ?We have a costumer there see this as a security risk.
Where is the best place to terminate a SIP trunk to a telecoms provider? CUBE or on CUCM itselfSomething is telling me CUBE but I'm not sure whySent from Cisco Technical Support iPhone App
We are running a new deployment of CUCM 9.1.1. We are running SIP trunks to our PSTN gateways and use PRI as connectivity to the PSTN carrier. The problem we are running into is that when we have the MTP Required check box checked on SIP trunk to o...
Hello, I have a 2801 router with CME installed. This router is connected via ADSL to a VOIP SIP service provider.I have two 7940 phones connected to it and I make phone calls using this VOIP system.My question is regarding the actual DSP chips. I kno...
We have call manager 8.0 and different kind of cisco phones such as 7941, 7942, 7961, etc connected to our subscriber. At random times on both internal and external calls, when a call comes in we answer the phone and say "Hello" and nothing. About ...
I have a home office that I need to setup for the owner. We have a 2851 with a GRE VPN setup at the office. At the home we have a 1841 router with a GRE VPN tunnel to the officeon the 172.16.0.0 netowrk, a 7960 IP phone, and a PC.Can I set up the r...
After configuring the 2911 in a lab environment, I need to verify the 7925G works but with no dialtone what can I do to ensure its configured/operating properly BEFORE I go onsite to install the 2911 ad 7925G? Any 7925G simulator should I need t...
We recently installed approx. 25 6945 ip phones at our location in Hawaii. Delay seems to be preventing the phones to upgrade firmware. All my work arounds have failed. Any suggestions. Here is what I have tried:Load server - installed all necessary ...
Hi Experts!My customer have this scenario:400 remote sites (4 - 8 IP Phones).2 CUBE to sip-to-sip calls with ISP.Topology: Site1 -> Site2 -> Cluster CUCM -> Gateway CUBE -> ISP (SIP)Site3 ->Site4 ->...
I just finished setting up a Background image for the Cisco phones in the company. I can already select the background image by going manually on each phone Settings-User Preferences-Background Images, but we have almost 500 7542Phones in the Enterpr...
