Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,There is a CUBE (12.4(25c)) with SIP trunk to telco on public IP. CUCM is connected to CUBE with SIP trunk to private IP on loopback interface. Though the default behavior for media to flow through in voice service voip and dial-peer configurat...
We have MCS7835-H2s running CUCM 6.1(3b)SU1. We want to upgrade to 8.6. Looking at the compatibility charts it looks like these servers are supported for a bridge upgrade only. But if we upgrade the memory to 4 GB and the hard drives to 146 GB wou...
Hi,When i place a internal call from CME to a CUCM, the ipphone 6921 ask me to press softkey ´acct´ , if I dont press anything drops the call, in order to place the call i need to press ácct´ and the * I have configurated a fac custom pickup group an...
Hi all,I have configured a cisco 7911 with the following configurations:ephone-dn 40 dual-line number 999 no-reg both label Faith_Test 999 name Faith_Test corlist incoming In000-002-98 huntstop channelephone 40 device-security-mode none mac-addres...
Hi allI have a question the CCM 4.3 support windows 2000 or not ?because I have a CCM 4.1 with OS windows 2000 and I want to upgrad it to CCM 4.3.Thanks and kind regards.
Hi All,I have an issue with our iPhone jabber clients with CME. The issue was first brought to my attention as users couldn't log into their CUE voicemail. They would dial the mailbox extension, get the prompt to enter their mailbox number and press ...
Hello, I am trying to get either of our in office 6921 or 6945 phones to transfer. In most cases as soon as you hit the transfer button it puts the person on hold then you type in the extension to which you are transfering, then hit the button again ...
We are having an issue with so far 7962's some are advertsing G711 and others are stuck on G722 when being transfered to a UCCX or voicemail. User being transfered receives a busy.Software Version: 8.5.1.14900-5 Problem Details: When internal phone ...
Hello everyone!How can I match an outbound call to a dial peer. For example I need internal number 1000 to go through dial-peer 1 and internal number 1001 to go out through dial peer 2? And another question regarding inbound callsHow can I make an in...
hi,we have a CUCM 7.1 and a 2821 ISR with SRST 7.1.I created a SRST Reference at the CUCM and set it to the Devicepool of the phones.The 2821 is configured as a h323 gateway.I configured the call-manager-fallback at the gateway as following:call-mana...
Hi ,We are unable to dial out when we place call on hold from 6945 model.but it is working fine on 7965 phones.I configured all ephone-dns as a dual-line.Please help how to resolve it..CME 8.8 version
Hi,Using a 2921, IOS 152-2.T (cme 9.0) from a 8961 sip phone, call transfer to any type of phone from failed : "Cannot Complete Transfer"call transfer with a sccp phone works fine.Any thought ?DV------------Feb 14 09:14:42.023: //-1/49ACC544AF19/CCAP...
I was using for almost 18 months the CCA v3.x very well (upgraded two times the previous versions), 3 months ago and I started sharing configurations and settings with the Cisco SB Office Manager, yesterday after enabling the VPN for a user in the CS...
Hello,My boss buy a Cisco IPPhone 7975, and he absolutly want to use it.But our telephony is on the SIP protocol, so I want to pass this phone on SIP mode, I have downloaded the firmware from the cisco website but I don't how I can put them on the ...
i use the CUCM with version 8.0a sip trunk connection with a asterisk ,now everything is ok but the DTMF ...the asterisk need inband DTMF,and i only known the CUCM support RFC2833....I want to know how to config cucm to support inband DTMF...
