Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all,anyone seen something like this before:This is the router we are using as voice gatway:Cisco Router 2801IOS: c2801-advipservicesk9-mz.124-24.T22 FastEthernet interfaces2 ISDN Basic Rate interfaces <----------- Two ISDN lines1 terminal line...
Hi, I've got 2811 with CCME. All ephones, including CIPC, in the local LAN and not so remote WAN segments are working quite well. There isn't much load on the router, only 5 ephones total, it's just a starting project.Recently we needed to provide te...
Hi all,I have a strange behaviour on one of our ISDN line (again):Everything is workin as expectes with one exception. One special external user tries to callour operator (DN: 00) but the call will fail (its only this user experiencing the problem).W...
HiIf you have a router that supports 100 ip phones in SRST mode but have 120 phones, is there a way of deciding which phones will not register?regardscolin
HiPlease note here we are not talking about the Fractional PRI E1 ( this is provided by the Service Provider).In our case, we have a full 30 channel E1 PRI provided from the Service Provider. We would need to fewer channels on the 30 Channel PRI E1, ...
What's the easiest way to get 4 digit dialing between to non-IP connected sites? I know this can be done with translation patterns, but does the UC500 support Centrex lines or SIP trunks?Thanks!
I'm having troubles making outbound calls. When 9 is dialed I get a busy tone and not secondary dial tone. I also debugged the dial-peers and it says there is no match????
Software Version: CUCM 4.2(3)sr4a2 Gateways MGCP This is the scenario. A call comes from outside of the organization to 76xx to CTI to a receptionist 47xxx. Then call is transferred to the bosses receptionist at DID 7665. Then the bosses receptionist...
I have a simple question about the SRST reference and it's relationships - just for my education. Why does the SRST reference in CCM reference an IP on the remote gateway? If my primary link goes down, why does this reference need to know/what does ...
We have a user that is looking for the following :When he is on phone with a client and his line is in use, he doesn't want to interrupt discussion by puting the line on hold in order to call his secretary. All he wants is to send a "beep" signal to ...
Hi,I have a CUCM server ver 6 with with 2 Voice GW. The protocol used is MGCP. We are planing to relocate the CUCM to a Data Cente. But the phones phones and the Voice GW will remain in the old locations. We are not plannig to change the IP addr of ...
Hello,I have an MGCP gateway with 4 FXO. Only 2 FXO er connected to Telco lines.One FXO/Line hehaves very normally. However, When I call the num asssociated to the second FXO the attendant internal IP phone keeps to ring one time then stops , then ri...
Hi,I am trying to configure SRST fallback mode:telephony-service srst mode auto-provision none<--removed ->Till now I used:call-manager-fallbackThe callmanager has several BRI interfaces and are under H323 controll. When callmanager works the call is...
Hi,I factory resetted a 7906G Cisco IP Phone, but its showing as upgrading on the display.The CUCME is in a remote location and now am not able to manually assign any configuration on the phone as i am not able to access the Settings Page.If some one...
Hi,We have CUCM 7.1, Unity Connection 7.0, CUPS 7.0, CUPC 7.0, IP phone 7911, 7965, 6921We have voice mail, hard phone and CUPC for all users.We want to activate same Voice mail box on CUPC & IP phone. So that whenever any Voice mail comes on particu...
