Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I am having a lot of problems setting up a VWIC BRI in a Cisco 1861 that is connected BRI in Malta. As I am working on this remotely I am having a lot of difficulty getting information to configure this.The ISDN's will be under MGCP control; howe...
Hello,After this upgrade all users with associated devices can't be accessed on CUCM administration, it just shows a blank screen. All other users without associated devices work well.Is this a known issue? Or am i doing anything wrong?Thanks for you...
I've got a couple 7935 conference phones that mysteriously "de-register" from the publisher (running CM 6.1), even though the other phones around them work fine. Their software load is 3.1(1), which was meant for CM 4 and earlier, so I want to upgra...
This used to work, but now it does not work. When users try to transfer a call using *xxxx we get a generic unity greating. "Welecome you have reach the unity system, etc etc.." It is properly setup in Call manager. How do we fix this, this used ...
Hi All,We have a UC520 system installed, it works fine in and outbound calls. All outbound calls show our primary number as the CID, however right now incoming calls only show the calling number.When I added this line to my PRI port:interface Serial0...
What causes the CoreDumpFileFound alert in RTMT? A better question may be what causes a new core dump file?
I have fax machines connected to a VG224 FXS gateway going out to the telco via a PRI on our 2811 Router. Both gateways are connected to callmanager 7 via MGCP. I am having issues where faxes to certain remote fax machines do not go through and I g...
What would be involved with this process? Ive done upgrades from 4.x to 5,6.x installs and had it use the DMA output. Is it the same process when upgrading 6.x to 7.x when using new hardware? Or do i have to upgrade the old hardware to 7.x the...
Hi,I need to make international calls from my CME.Can anybody help me with the dial-peer config for this:dial-peer voice 011 potsdescription international dialingdestination-pattern ? port 0/0/0:23forward-digits ?
recently uploaded cmterm-7941_7961-sccp.8-4-4.cop.sgn to my cucm7 cluster. I got complete from file upload. Now RTMT trace is saying it cant find the .loads file Any thoughts?
I have a user who needs to have a speaker phone function. While the calls come over the speaker, she can't speak unless she lifts the handset.I tried using a Plantronics headset but that doesn't work.Is there something I can configure in CUCM for th...
I have two requirements1. Setup number so that when a customer rings in it will ring on a certain number of phone and mask Company Name 1 on the Line when it is ringing to that the Agent will know which company the customer is calling and can answer ...
Hi,I have two hunt group and I want to setup prefix dialing where I can get the agents to type in some digits before the number they want to dial and it will mask out the DDI number.At the moment, if the agent dial an external number, the extension n...
Hi,We have CCM 6.X cluster and have 7960/7961 IP phones with 5 lines/buutons configured. I want to do a "Call Forward All" for the 5th line on the phone to a different number/extension. How can I achieve this directly through the phone.I am aware tha...
hi guys, i got a strange problem,I have CCM 6.0 which is registered with GW via H.323 .... my outgoing calls (from ip phone to PSTN) are working fine but for incoming (from PSTN to IP Phone) if i dont select any partition (i mean if i select none) th...
