Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have configured MoH for a UCM 6 cluster. I have assigned all the devices a MRGL that includes a MRG with the MoH servers in them and assigned audio streams at that device level. I am still ONLY getting tone on hold (3 beeps). I have never encoun...
Anyone using a Sprint SIP trunk with CUBE (IP-IP GW) with CallManager 5x/6x ? Any issues? Caveats? what authentiction/dtmf/codec are they using?
If I do a CFWDall from my IP phone to a second IP phone on the network. If someone calls my phone it does ring on the forwarded phone, but when it goes to voicemail it sends the call to my voicemail not the forwarded phone voicemail. Is this normal? ...
HiHas anyone seen a UK phone localisation file for 7.0.1 or 7.0.2 ? I cant find one on CCO. They have ones for US English and French, German, Greek etc but all the non US English ones (eg Canadian) are missing. CNA 1.9.1 won't let me set the region t...
Greetings,With a CCME 4.3 setup, I did limit number of digits any IP phone can dial as Call Forward All destination.However when accessing CCME GUI, users are allowed to set any CFwAll destination. Is there another command limiting this setting from ...
I have built a h323 gateway between a CUCM 5 and an Avaya 8700 IP capable PBX and created the appropriate Dial Pattern however when I place a call I still get a busy signal when I dial the number. I have followed the instructions found on this commun...
Does anyone know of any figures based around any impact on CUCM when using Route Patterns and using the delete/insert sections. The reason is that we have the following set up per site Route Pattern is 123.xxxx (123 site code) which is a On-net patt...
hi guys,i am getting strange problem while registering MGCP gateway with CCM 6.0 ... after configuring MGCP whn i try show ccm on gateway it showing me registered or Gateway in CCM it is showing unregistered ... after finishing the configuration on m...
Have issues in an office where most phones will reboot at the same time. I have looked at the affected phones error logs and am stumped by the java error.ERR 09:00:00.003015 NTP: Wed Aug 15 09:00:00 2007WRN 09:40:41.228020 JVM: Thread-3|cip.sccp.ce:?...
We have some phones in the corridor of a shop which are used by the customers to contact to the operator (hunt group 1090, with two extensions, 1000 and 1001). I would like to configure the phones to dial directly to 1090 (or 1000 if it doesn't work)...
Hi there,I got a question regarding this top:If there is no Media Resource Group List (MRGL) has been assigned to Device Pool, IP Phone (Device) and User Device Profie (UDP), what will happen if a call has been put on "Wait" (MOH) or a conference has...
Hi,I upgraded a CCM 4.1.3 to CUCM 6.1.3,Upgrade was successful all the phones except 7912 take the new loads. I have a problem with 7912 phones which is getting registered with their old firmwares,but not the new firmware listed in CUCM 6.1.3(In devi...
Hi,We have a customer that has a number of users with DECT phones that connect via Kirk IP system back to the CUCM. (So the DECT handset registers with the Kirk box, and the Kirk registers with the CUCM). Telephony all works fine, in that users can c...
Hi I have CCM ver 7 , once i go to phone then go to Directory Button then go to Corporate Directry , is showing me Directly error " Error , contact administrator " , note this problem on all phones . please can you help me ASAPthanks
I have two IP phones, 7911 and 7906 in CME. I want to change firmware from SCCP to SIP. How can I make the change?I have already the file cmterm-7911_7906-sip.8-4-4.cop but I don't have the procedure.thanks
