Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have tried to prepend 700 onto a route pattern using calling party transformation.the call is routed to the gateway and i have debug q931 running there so I can see exactly what is the CLID.So, for example I have a station with DN line 7820 and wan...
We've currently got a Call Manager Express installation with Unity Express module (AIM) and BRI NT/ST Vwic cards.There's an ISDN NT terminator box to which the CCME connects to. There's also a fax which connects to the NT terminator box.I'd like to s...
Hi,I have CAR in my Call Manager. I am able to get reports about individual extensions.When trying to pull reports based on users, I am not getting any thing. I have created users in DC directory in Call Manager and mentioned the Telephone number in ...
Hi, I have some basic queries about VG224.1) How many Ethernet ports VG224 is having? Is it possible to configure redundancy oe etherchannel between these ports?2) How many maximum number of ad-hoc conferences can be initiated from an analog phones c...
Hi, Just wanted to run a quick check with you guys. I appreciate the help. I have data on vlan 10 and voice on vlan 20. For the switch port that CCM connects to, would I assign it as an access switchport, but in the voice vlan?interface FastEther...
Problem:NTP service is running, but time is not updatingPublisher is set to use 192.168.1.201 as the NTP server.The subscriber pulls time from the publisher.IP phones pull time from the subscriber.The Publisher is running about 2 minutes slower then ...
Dear Sir,I have Cisco Unity 4.0.5 and the C drive is out of space there is a folder size of which is 11.6 GB and the path of that folder is as below.C:\Program Files\Microsoft SQL Server\MS SQL\Data\UnityDb_Log.LDF How can I decrease the size of this...
We have a location with a 4 port FXO card with 4 POTS lines. They started having problem where they can't make calls. We tested the 4 POTS line and they all work.Any ideas on what is causing this problem2811 running 12.3-11.T8 Call Manager 4.2(3)
I need to block incoming calls based on the calling number. I have found information online about how to do this if your gateway is H.323 already. However, I am using CallManager connected to a gateway using MGCP. Therefore I believe there must be...
I have a vg224 running mgcp and it works great. Howerver we have also requierments to configure the vg224 also with srst. I read through the posts that sccp works with srst but has issues with fax passthrough.If I wanted to keep the mgcp configuratio...
Hi,I am deploying two CME (Cisco 2800 series routers with image 12.4 (11XJ))locations with IP telephony. I would like to connect these two locations through VPN Internet connection without using the PIXs.Has anyone already had this requirmet and expe...
Can anyone verify if the end of life 2948-GE-TX supports auxilirary vlan? The configuration guide specifies that the 4000 series does but nothing mentioned for the 2948.Regards,
When I call from my ip comm (from vpn) to another phone I have no problems. when I attempt to go out over the sites local PRI's I hear fine but cannot transmit voice accross the PRI's.
Hi. I have a UC520 running CUE. When I install CUE, it automatically sets itself up with US settings; US timezone and the US voicemail (voicemail recording says press the pound button... in UK we need her to say 'press the hash button...) How do I ...
Two problems exist.1. Receptionist can place a call in park and the call can be retreived by phone. However, she cannot retreive the call herself using AC. She gets"failed to make new call" and hears "your call cannot be completed as dialed"2. Th...
