Dear AllI have a PC and I want to send the video message out through multicast from the PC. Do you think I need to have some special tool installed in the PC to start the multicast ? The PC is directly connected with a routerThank youFrank
Dear AllI have a PC and I want to send the video message out through multicast from the PC. Do you think I need to have some special tool installed in the PC to start the multicast ? The PC is directly connected with a routerThank youFrank
I am getting the following error after a circuit upgrade from a ISP CSME to a ISP ASE (Switched Ethernet). The remote end is the one that is producing the error below. I have posted the config on the Catalyst switch. They are 4510's with Sup7 engines...
I segregate my routers into different syslog groups, to that end I have setup "logging facility local6" on my Cisco 2851 Internet router. But I am still getting the following messages in my Syslog2015-04-11 00:32:03 Local0.Alert localhost FA: syn ...
We can use the command below to display total traffic:sh int port-channel 123 counters etherchannelIs there any way to display average traffic?
Hello,we have 2 switches in stack, last night switch 2 was removed from stack and got rebooted and again it got back in stack.Switch -2 entered into the provisioned mode for certain span of time. snap shot is attached .Apr 9 02:36:25.266 IST: %STA...
Hi All,I have been facing on one of my Router WAN MPLS Link Connected Interface, FE. In logs, I am getting below logs continuously and have done below troubleshooting.Router Model - Cisco 1841, IOS (C1841-ADVIPSERVICESK9-M), Version 12.4(19b).Interfa...
Need help on BGP where seconday router interfaces,RX is not happening.Site has two MPLS links which are in active active mode, but on one of the router Rx load is not happening.Please advice sh int g0/0 on primary link Input queue: 0/75/0/0 (size/ma...
Hello All,I am facing some issue on BGP.I configured BGP on cisco 1905 but . BGP neighborship is not forming.I am attaching my Show tech and BGP debug.Please help me to out on this.
Have a small doubt : what is the difference between BGP attributes AND BGP Communities ?
Hi, I wish to implement DMVPN usning single hub, single router with dual ISPs and have 10 remote spoke locations connected single ISP.Want to create two tunnel interfaces from each spoke, one is primary (ISP-1 at HUB) and another (ISP-2 at HUB)is bac...
We have 50+ sites on our MPLS network. All are connected quite successfully and all have a completely individual private AS number eg router bgp 65001We are about to bring a new site online and our telco provider has given us the details but this tim...
Hi All,I have a two different ISP s configured BGP with Core Router. I have to set path for some ibgp sessons goes through isp1 and remainig ibgp sessions goes through isp2 and If one isp down means another isp have to take over all ibgp sessions.I ...
Hi all,Well this is an interesting one, i have a tunnel configured between two 2921 routers that used to work just fine, we had an management access issue on one of the routers and it had to be rebooted, all looked fine until one of OSPF adjacencies...
Hello, I am at a loss at the moment. I am trying to swap an old firewall with a cisco 2900 router. I configured route-map's in conjunction with NAT. The users in the internal network are able to access the www just fine. They are getting a public ip ...
is it possible to make IPSEC_over GRE with secodnary IP??Site_1 Primary IP with crypto map - Tunnelling - Site2 Secondary IP with crypto map.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-02-2024 11:49 AM | ||
05-02-2024 10:54 AM | ||
04-26-2024 09:18 AM | ||
04-26-2024 07:58 AM | ||
04-26-2024 05:26 AM |
User | Count |
---|---|
14 | |
8 | |
4 | |
2 | |
2 |