Server Networking

Hi out thereWe have two DC's with 10G interconnection in  between - these connections are run as L2 links - put into a set of  nexus 5000 (the old nx5020) - acting access-switches - and uplinked to a  set of nexus 7009 which act as L3 switch for us.W...

Hello all,I have an issue with the installation of the VEM. The VSM installation went fine and it can communicate with vCenter.Below you have some information that you may find useful.vSphere 5.1.0 (Trial)Nexus 1000v - 4.2.1.SV1(5.2b) (Evaluation)The...

Hi,I have deployed UCS director in my lab that is not yet connected to a domain.UCS director version is: 4.0.0.2Unfortunately have forgotten the password and hence can't log back in.Can some one help me on how to reset the password, whether using ssh...

With Vinayak SudameWelcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco Nexus 5000, 6000 and Fibre Channel over Ethernet with Cisco expert Vinayak Sudame. He can cover quest...

Recently deployed Nexus 7010 in the core of our network.DHCP Relay is configured on all SVIs, but certain hosts cannot PXE Boot or obtain DHCP leases.Various servers set the "broadcast flag" in the DHCP header when they send DHCP-Discover packets dur...

I can't see "feature lldp" available in Nexus1000v CLI or configuration guide. Does it support it? From data sheet, it seems to support.

Hi,Please be so kind and provide me a preinstalled nexus 1000v. (for learning purpose)Tank you!

If ruining fabricpath in a leaf, spine (vpc+ l2/l3 boundary) and l3 core design is it possible to breakout on a classical ethernet dot1q trunk from the spine to temporarily pass the fabricpath vlans to another site (catalyst only)?

Hi guys,I have to connect 2 DC with dark fiber in vpc.First side there are 2 6k in vss, on the other side there 2 N7k in VPCi will make hsrp localization to have local routing on each DCit's ok for the hsrp hellos filtering configurationusually when ...

I am having ESXi 5.1 with two (2) Nexus 1000v  domain (VSM-A in domain ID 100 and VSM-B in domain ID 200).  There is only single DC and vCenter server. I cannot vMotion between the two clusters that is managed by different Nexus1000v system although ...

Hello Gents,I cought into weird situation after upgrade VMware ESXi 5.0 to 5.1 on UCS C200M2. Before upgrade I have had server with configured static adapter-fex VNICS and floating/dynamic vm-fex interfaces working perfectly in DirectPathIO mode for ...

how to configure EEM on Nexus 5K to monitor FEX? I would like to configure it so that we get email as soon as FEX goes down. 5K is running 6.x and it supports EEM as per config guide. BIOS:      version 3.6.0  loader:    version N/A  kickstart: versi...

Hi,I'm trying to deploy a new FEX model 2232TM-E on a 5548UP running version 5.1(3)N2(1c)According to the release notes, this fex should be supported on the N5K software versionYet I get this debug:2013 Nov 14 11:12:02.139019 fex: Cardinfo: Invalid c...

Ok. This is completely unrelated to server's HW stuff as it appears much before service-profile association with server itself. Specifically error arise when U finish to configure service profile. No extra-actions while configuring service-profile we...

My existing VM blades are running VEM410-201210150101-BG. We plan to upgrade the VSM to 4.2.1.SV2(2.1) including VEM to version VEM510-201306160101-BG in couple of weeks time.I have installed newer VEM on the new blades that will be joined to the sam...