hi, how to configure telnet/ssh on ASA 5550 from outside.Thanks
hi, how to configure telnet/ssh on ASA 5550 from outside.Thanks
Greetings,I have a very strange issue. I have configured a 3005 concentrator with an address pool that is in the same subnet as the private interface. When I try and connect a client...I get an error stating that NO AVAIL ADDR with a further explan...
hello everybody : My VPN concentrator 3020 always hang up without any error log after i use webvpn function at this device. Maybe it often happen one time a week . and i already upgrade to the last software version 4.7.2 . I check the event log and n...
Hi, We need to install Cisco VPN client in inside our network. What ports need to be opend in the Cisco firewall? Please advise.
HiIm trying to setup a L2L VPN between 2 ASA.ASA at site A has a public IP address.At site B, instead, the ISP router forwards all the incoming traffic for a pool of public IP addresses to a group of private addresses configured on the ASA.I wish to ...
Hi,I am having problem accessing the Internet from the LAN behind a PIX 501. This has been working for months but suddenly I discovered that Internet access is intermittent. Access to the Internet works for about 10-15 minutes and then goes down. Whe...
Hi,I have a working remote access SSL vpn on my asa 5505. However, the same SSL vpn does not allow for users to connect using the AnyConnect client software.If I enable an alias for this SSL group, both the AnyConnect and the SSL vpn login will work ...
Hello,Any one can tell me how I make the Cisco VPN client reconnect automaticaly after disconnection ?Regards,
Looking for feedback on using a Cisco 7206 to terminate Lan-to-Lan tunnels and using same 7206 has EasyVPN server. Are there any issues with doing this?
Does ASA5510 use Aggressive Mode when setting up VPN tunnels?Any link where I can get more information on this?Also, is there any configuration on the ASA that can be done to mitigate the vulnerability mentioned in the link below?http://www.cisco.com...
Guys,Need experts advise on whether new ASA software releases support VTIs. If anyone have any supportive doc explaining VTI on ASAs and how to configure them, enclosing that would be a great help.Thanks a lot in advance.Regards,
we currently have a vpn 3000 concentrator that is connecting remote users, had a lightening storm that killed our Radius server, in the process of reconfiguring it. the IAS server is part of a domain and vpn users should be checked against AD for pe...
I am setting up an ASA5505 for IPsec VPN and cannot get the VPN client to connect.The modem/router at the ASA site is a ZyXel 660. How do I get the ISP-provided DSL WAN address to the ASA5505? Port forwarding on the ZyXel? Basically, forward all traf...
Greetings- This command causes the my manamenet software to think there is a new version of configurtion, and to save the configuration. Is there anything that can be done on the Firewall side? I am already looking at somehow ignoring it on the m...
Is it possible to configured policy based routing either on Pix or ASA? If so I wanted to know the commands or the link where I can able to go through before implementing them on live.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-27-2024 02:28 AM | ||
04-26-2024 05:58 AM | ||
04-25-2024 07:36 PM | ||
04-24-2024 01:26 AM | ||
04-19-2024 08:08 AM |
User | Count |
---|---|
6 | |
4 | |
1 | |
1 | |
1 |