The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
Ive a pair of new UCS-FI-6536s and they are all set up and working fine in IMM but we cannot SSH to them as we did on the old FIs.They are on the same VLAN as the old FIs and there are no firewalls inbetween them.Does anyone know if this is even poss...
I get the regular connect and disconnect messages ie the 7220xx messages but I tested several bad password attempts and they do not get logged. is there a way to log this?Would be interested in creating an EEM that would alert on a significant amount...
HiI would like to block incoming call from 1-2 number, i tried creating a rule to reject but not working...extracts of my rules are give below, am I missing something here? voice translation-rule 2rule 1 some old rules.....rule 2 some old rules.....r...
Hi anyone using radware as loadbalancer for wsa? Do we need to change anything in wsa side? We have given radware LB vip in the proxy settings of users but request is not reaching WSA.anyguide is available for the configurations.
Hi, as the title says, I am unable to connect to my Cisco Secure VPN after updating my OS from Ubuntu 22.02 to 24.04. The error I receive is"You are missing the required libraries for the authentication method you requested."Upon closer inspection, t...
Hi Guys.We are running Firepower 3140 Appliances. There are 2 * 40Gbps connection. The Physical (ETH2/1) 40Gbps interface has the MTU set as 9000 whilst the Sub Interface (ETH2/1.10) and (ETH2/1.20) has the MTU still at 1500In this scenario,1. Is the...
My name is Zake and i want to ask how to setting severity in Cisco Estream, i use Cisco Firepower 3120 and want ingest log to Azure Sentinel. I was successfull to ingest log but there is too much log i got, when i see there is too much information se...
The user computer switches to voice vlan but the port configuration has both access vlan and voice vlan.Avaya ip phone switches to voice vlan.The user computer also switches to voice vlan.What could be the cause of this problem?Port configuration swi...
Hey guys,I have an old SX350 running version 2.5.0.83.Currently when i'm trying to output a command like show running-config I get prompted to show more of the command as it doesn't show all at once.I am able to use the terminal datadump command to s...
we are using Cisco Aironet 1815i Access Point as a WLC and Access point and need to be upgrade the firmware version 8.5.140.0 to 8.10.185.0. please suggest the step by step process that we need to be followed.
Hello everyone, is it possible to generate a report or something that says how many minutes during the month or last 3 months, a FTD was out? For example, if I go to "Monitor-statistics" I can see the uptime of the device, that is, how long it has b...
Hi All, I'm having a weird issue where I cannot access via CLI on the WLC 9800 using radius authentication user, while I can do so with the same user via GUI. I configured AAA servers and groups to match correctly and activated the HTTP and VTY acc...
I'm trying to configure a guest SSID on the Cisco 9800 with a 5520 as the anchor controller. The SSID has a CWA portal hosted on the external ISE appliance. Normally the flow (which is still working on the existing 5520 foreign controllers) is that y...
I recently started working at a new place and I am trying to understand the network config.There are 2 48 port 9300 switches in place, running the latest firmware.They are running a single 1gb trunk port between the switches, but when I dig into the ...