Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1937087members
1263663discussions

Community Activity

%RADIUS-4-RADIUS_DEAD

Trying to authenticate I have this error as shown, can anyone help me!*May 11 12:38:20.482: %RADIUS-4-RADIUS_DEAD: RADIUS server 192.168.100.3:1812,18 13 is not responding.*May 11 12:38:20.482: %RADIUS-4-RADIUS_ALIVE: RADIUS server 192.168.100.3:1812...

Jason2005 by Level 1
  • 94 Views
  • 2 replies
  • 0 Helpful votes

Secondary WLC over the internet for APs operating on Local Mode

Dear Gents,          What are the recommendations that should be followed if we have a local site with wireless APs operating in Local Mode and registering on a local Primary WLC on the same network.  and in the case of Primary WLC failure, the APs w...

HNETENG by Level 1
  • 0 Views
  • 0 replies
  • 0 Helpful votes

Error opening tftp server

 When I connect to the switch(2960x) for the first time with the console, I get the following error and I cannot enter any commandError opening tftp://IP/ios name.bin (Time outThank you for helping me

FirePower 1100 lost smart registration

I have a FirePower 1100 for my home lab and for some reason, it lost DNS connectivity and lost registration. I did not notice and now I can't deploy changes. I connected to the CLI and tried to ping from system. When I try to ping from system I get t...

CBS350-8P

Hi all, I have a cbs350-8p-e-2g with version 3.4.0.17, every time to reload it will show below message but I didn't make any configuration changes. Is it a bug ?"You haven't saved your changes. Are you sure you want to continue ?"

Can't make my wireless devices connect with WPA2 Enterprise

So I cant make my 2 laptops and 2 smartphones conect to my wireless device if it has WPA2-Enterprise Security. I don't know why it happens because when I eliminate the security it connects perfectly. Here's the .pkt if anyone can figure it out why

atrumar by Level 1
  • 120 Views
  • 1 replies
  • 0 Helpful votes

RIP routing table not loading routes.

Hi Guys n Gals,I am having a bit of trouble with an assignment I am doing in packet tracer.I don't have the files handy until the eve, so will send pics/files later if required.My problem is that I have an access router connected to 3 separate cluste...

DHCP Server issues DOT1X

HelloAfter I have setted every policy on the switch and everything is working fine through an ISE authentification via dot1x, now server cannot reach its gateway in order to give IP DHCP addresses to the hosts on VLANs!Can anyone help me please

Jason2005 by Level 1
  • 112 Views
  • 1 replies
  • 0 Helpful votes

Aironet-1562i-outdoor-access-point is not powering ON

Hi, We have installed Aironet-1562i-outdoor-access-point one of my project, While installation it was getting power from the 4506-E Switch and it was registered with Wireless LAN Controller, but now the Access point is not getting power from the swit...

Arjun@26 by Level 1
  • 535 Views
  • 3 replies
  • 0 Helpful votes

WLC - mDNS Bridging Between Wired LANs

Does a WLC support bridging mDNS between wired LANs only? More accurately, will it respond with mDNS service provider info learnt from wired LANs to mDNS queries coming from wired devices in other LANs? I had assumed so, but debugging today I'm seein...

tresdodi by Level 1
  • 99 Views
  • 1 replies
  • 0 Helpful votes

Cisco Phone system

Hi, I'm looking to get some assistance or guidance on this old phone system. Looking to see if there's any 3rd party vendor that is willing to help troubleshoot some issues. Cisco Unity Connection version 8.5.1ES65.13900-65Cisco Unified CM Administra...

Abrar786 by Community Member
  • 101 Views
  • 2 replies
  • 0 Helpful votes