MPLS

Hi folksI'm hoping someone can help me with the following issue(at least I think it's an issue).We recently installed a remote PoP with a service provider(who are using something called Martini tunnels??) ethernet link providing the WAN link.This has...

Hello Team,I have multiple 10G and 1 G ethernet connected between the PE routers and doing L2 VPN over that. Just curious about how it does load balancingfor the traffic across the vpn sitesThanksHarish

Hi Guys.I have one problem.The scenario is from ISP get full view in VRF OUT on WAN1 , then export route from VRF OUT to VRF CUSTOME1 on AGR1 (WAN1 and AGR1 is cisco 6509). I want export only default gateway from VRF OUT:ip vrf OUT rd 333:1 export ma...

HelloI am having difficulty understanding the following commands:int ATM 3/0.2 mpls ip mpls atm 2-3 mpls atm control-vc 5 31Should I not have mpls atm control-vc X 31 where X either value 2 or 3?I thought the 5 was the VPI which must fall within the ...

Dear Gurus,Does EoMPLS passes multicast traffic? Before my customer can pass multicast traffic (video) thru our Metro-Ethernet network. What we did is migrate the connection to our EoMPLS network, and then suddenly the video is not working.Thanks.Jef...

Hi AllI have the scenario below:PC1----eth---Cisco ASR1004(1)---stmx link------CiscoASR1004(2)----eth---PC2I would like to use eompls so that pc1 and pc2 are in the same subnet.I have configured the xconnect on a vlan subinterfaces enabled mpls with ...

Hello I have some TE tunnels configured as follows:interface Tunnel5 ip unnumbered Loopback0 load-interval 30 tunnel destination 10.1.5.5 tunnel mode mpls traffic-eng tunnel mpls traffic-eng autoroute announce tunnel mpls traffic-eng priority 7 7 tun...

Hi All,Network Topology:pc-1 -> switch-1 ->7606-1 <---> 7606-2 <-- switch-2 <-- pc-2- All the "1' devices are geographically separated from all the "2" devices.- There is a /30 linking 7606-1 and 7606-2 core routers with each other.- MPLS is already ...

Hello,sorry for some kind of completly newbei question, we're starting a small IPS business and need some advice for our backbone platform. We're getting some utagged and transparent Ethernet interfaces on each POP (may be 20-25 distributed over one ...

Hi every one.im in situation that i have 3 routers.R1<-->R2<-->R3R1 is R2 ibgp peer and r2 is r1 ibgp peer.also r2 is ibgp peer with r3.my under laying routing protocol is OSPF and im running MPLS between these routers.I have VPNA on R1 and also i ha...

Hello Everyone,In an effort to estimate bandwidth usage on an MPLS upgrade and rollout we have been tasked with determining what bandwidth is required without use of baseline measurements on live data.Would anyone have a table or chart of applicaiton...

Dear Experts ,I want to have my different offices to use same IP address range (from a centrally managed DHCP server)  . Is this scenario possible with MPLS L2 VPN ?I know that we can do L2 between two branches by using xconnect  but what if i have m...

If the packets are fragmented in ingress and QOS is used, Does the QOS will be maintained after fragmentation. Like in GRE we have QOS pre classify to preserve the bits.regardsshivlu jain

DearsI have one branch connected through MPLS to meThe branch side is ATM to Telco and on my side it's connected to Telco thru Gig ethernet .interface GigabitEthernet0/3.65 encapsulation dot1Q 3456 ip address 192.168.1.1 255.255.255.252 mpls ipinterf...