is ciscoworks 2.6 supported on win server 2003 64 bit
is ciscoworks 2.6 supported on win server 2003 64 bit
Hi,I'm having problem in USerTracking to IPPhones, he brings the information such as Phone Number, Phone, Description, MACAddress, etc.. However, no information where they are connected (Device Name, Port, Port Name).The usertracking to EndHost is fu...
When starting Campus Manager we have ANI server Error message:In ani.log there is alert: I= 0value *.*.*.* I= 1value 6 I= 2value 12010/07/12 12:53:31 main ani MESSAGE DBConnection: Created new Database connection [hashCode = 3405865]2010/07/12 12:53:...
Hi All,I want to use the NMS to collect our T1 usage over the time. "show isdn active" can give me the current number of calls occuring in the gateway. Our gateways are 3845, 3825, 2811 service routers. Is there any MIB which can tell this statistics...
I've setup an udp-jitter operation with codec g729 on a cisco 1761 to run on port UDP 51140 (destination) and an ip sla responder on the far end side. I see that control packets are received and get a MOS and ICPIF value as well as RTT. But I do not ...
I'm trying to integrate the LMS 3.2 with ACS 4.2 and give to some user group rights on playing some LMS Role on some network devices group, but unsucceed. Integration itself was painless, but I can't use th LMS in way it should be used.It's OK, when ...
For the past two months our CiscoWorks appeared to be completing the daily sync archive job but if I open a record from Device Center for a device that was shown as "successful" collection status for Config Archive the Device Center record shows an i...
Dear,I am trying to get all ports on devices with the following specs :+ macro description vi- authentication periodicThe strange thing is that RME takes only one of the 2 lines, how do I configureRME so I have all the ports with the macro commando a...
Hello,This device has two power supplies, when one of them fails LMS (DFM) doesn't detect it.What is the problem?I attach some information.Thanks
Hi,We have a mater LMS server and three slave server. I always see this problem on one of the slave server. DFM DCR list is always out of sync with master DCR in this server. The RME on the same server is perfectly in sync with the DCR.In DCR under ...
Hi,I hope someone can help me. I have a Problem with the Device Fault Manager 3.2.0 on a Windows standard 2008 SP2 (32 bit) Server. I can't create Notification Groups, the failure is "There are no devices in the system (in Known state). I see on the ...
we have setup sysloganalyzer in LMS 3.2 and alert us via email when certain syslog messages are received.However our email are flooded with tonnes of email. Is there any way to place a limit say 3 alerts from sysloganalyzer. The switches will still g...
Does anyone has an EEM script which can bring down the interface when it sees a ospf neighbor failurethanksAmbi
Hi.I'm after a reboot on LMS 2.6 server, the CM home page started showing the following message: "Cannot connect to ANI Server since it is down". I followed the procedures as in the thread "Ciscoworks ANI server cannot connect, Joe Clark please help"...
Hi Everyone,I am unable to generate a syslog report for most of the devices. When I checked syslog.log it appeared that these same devices are not logging there as well. Action taken are:-restart daemon manager-restart server-unsubscribe and subscrib...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-23-2024 05:52 PM | ||
04-23-2024 12:20 AM | ||
04-16-2024 04:45 AM | ||
04-16-2024 01:33 AM | ||
04-13-2024 12:00 PM |
User | Count |
---|---|
2 | |
2 | |
2 | |
1 | |
1 |