What would be the commands to setup Netflow on a Cisco 2811 and are there any drawbacks (dangers)of doing so.
What would be the commands to setup Netflow on a Cisco 2811 and are there any drawbacks (dangers)of doing so.
Hello,we have some problems with gathering the Netflow statustic on our 6500 SUP720B and need some other solution. the problem is quite simple - netflow table on SUP720 goes full very fast, in 5-10 seconds and the netflow data statisctic is not fully...
Hi Folks,How can I tell what patches (rme, cm, common services etc) have been installed on a LMS 2.6 server? Software Update shows me application versions, but I want to see what patches have been installed.Cheers, Steve.Resolved....Can't see the fo...
I have 100 3750 switches and I would like some automatic way to distribute new IOS, and configuration information. What tool can be used for this?
Would I be able to import the backup from a higher license count install of LMS 3.0 to another one with fewer licenses? What potential gotchas could there be even after the restore were successful?Also, what does it mean "CWLMS-3.0-100-K9" is "not su...
Hi,I am trying to configure the sending of basic snmp traps on a FWSM running 3.2(1) to ServersAlive and have had some success.Purely for testing purposes, I am able to get alerted on sending snmp requests to the FWSM with bad authentication.Accordin...
Hi,Is it possible to use IPM to monitor a interface in core switch for any traffic.Or do we need a source and a destination for using IPM?with thanks in advancesathappan.s
Hi folks!!In order to run restore backup in background mode, I need that this script doesn't ask to me, if or not want to overwrite the Certificate!hera you are a log example<Certificate restore starts>WARNING: Cannot evaluate the hostname, hence the...
I am running WCCP in one of my interfaces, and exporting flows to the collector. Do I need any special configuration for NetFlow while runnign WCCP?
Hey guys,I read through the documentation and saw that to configure netflow for the PFC, you use the mls nde commands. Thats all straighforward.What I dont get is for the netflow on the RP, they tell you to use "ip route-cache flow" command.What I co...
I have 295 devices added to LMS inventory (to prove the there is nothing wrong with the setup/deployment).Now that i am trying to add a device (My NMS is placed at Site B...Here is the archTest_Swicth -> Access_switch_Site_A --> Core_Switch_Site_A --...
I need to change the hostname on a few switches, so I want to the the Parameterized templates in NetConfig.I've used the following parameter file:<DEVICE NAME = mySwitch><CMDPARAM NAME = hostName><value>mySwitch</value></CMDPARAM></DEVICE>My template...
Hello all.I'm running CW2.6 which was upgraded from 2.5, and had a license change from restricted to unresticted on 10 Sept. Recently (3 Oct), Campus (ver 4.0.6) has stopped doing a device discovery at either its scheduled time, or on demand.Any suge...
Hello,we use CA Spectrum to manage our cisco and enterasys network components.When there are any ospf problems like neighbor changes both cisco and enterasys send traps to spectrum.Traps from enterasys are correctly shown in spectrum including the ip...
I have a 3745 with a 36 port switch module. I want interface F4/0 to monitor F4/11. Under the interface commands I do not see the port monitor command. Not sure if this is possible or not.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-23-2024 05:52 PM | ||
04-23-2024 12:20 AM | ||
04-16-2024 04:45 AM | ||
04-16-2024 01:33 AM | ||
04-13-2024 12:00 PM |
User | Count |
---|---|
2 | |
2 | |
2 | |
1 | |
1 |